Clarke 6501661 Скачать руководство пользователя страница 17

17

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TROUBLESHOOTING

Problem

Check

Solution

Motor stops and 
will not run.

1. Defective/broken on/off
    switch.
2. Damaged power cable.

3. Open circuit, loose
    connections or burned out
    motor.
4. Blown fuse or circuit breaker.

5. Low voltage.

Send to your CLARKE dealer 
for repair.
Send to your CLARKE dealer 
for replacement.
Send to your CLARKE dealer 
for replacement.

Replace fuse or re-set circuit 
breaker. Turn off other 
machines on same circuit.
Check the power supply for 
correct voltage. Use 
another circuit or have a 
qualified electrician 
upgrade the power supply.

Motor will not start 
and fuses or 
circuit breaker trip 
out.

1. Short circuit in motor or
    power cable.
2. Incorrect fuses or circuit
    breakers.

Send to your CLARKE dealer 
for repair.
Replace with correct fuse or 
circuit breaker for the circuit.

Motor fails to
reach full power.

1. Overloaded circuit.

2. Unsuitable extension cable

Turn off other machines & 
retry.
Replace with correct size
extension cable.

Noisy operation

1. Incorrect belt tension.

2. Dry spindle.
3. Loose drive pulley.

Adjust belt tension. See
Replacing the Belt on page 
12
Lubricate the spindle.
Tighten the retaining set-
screw on the pulley.

Содержание 6501661





















Отзывы: