manualshive.com logo in svg

Clarke 6460072, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke 6460072 Скачать руководство пользователя страница 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY WARNINGS

WORK ENVIRONMENT

1. Keep the work area clean and well lit. Cluttered and dark areas invite 

accidents.

2. DO NOT operate power tools in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust.

 

Power tools create sparks 

which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Anyone 

entering the work area must wear personal protective equipment.

 

Distractions can cause you to lose control and fragments of work or a 
broken blade may fly away and cause injury.

4. Store power tools properly when not in use. Abrasive products should be 

stored in a dry, secure place out of the reach of children.

5. Please read these instructions carefully and retain for future reference.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. NEVER modify the plug in any way. 

DO NOT use adapter plugs with earthed (grounded) power tools.

 

Unmodified plugs and matching outlets will reduce the risk of electric 
shock.

2. DO NOT expose power tools to rain or wet conditions.

 

Water entering a 

power tool will increase the risk of electric shock.

3. DO NOT abuse the cable. NEVER use the cable for carrying, pulling or 

unplugging the power tool. Keep the cable away from heat, oil, sharp 
edges or moving parts. Damaged or entangled cables increase the risk of 
electric shock.

4. Position the power cable so that it cannot be inadvertently pulled or 

pinched and where it does not cause a trip hazard.

5. Never use the machine if the electric cable or plug is in poor condition.

6. This machine is designed for indoor environments and must not be used for 

other purposes.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN 
PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Содержание 6460072

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды