manualshive.com logo in svg

Clarke 6460072, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke 6460072 Скачать руководство пользователя страница 17

17

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

CLEANING

Accumulated dust and chips should be removed from inside the bandsaw 
frequently. Open the upper and lower covers, use a soft brush and/or vacuum 
cleaner to remove sawdust. If compressed air is used, ensure it is set to no 
more than 10 psi and ALWAYS wear eye protection.

At the end of every work session, clean sawdust away from the motor vents.

CHANGING THE SAW BLADE

1. Remove the U shaped blocker 

from the table.

2. Open the upper and lower 

covers.

3. Set the upper blade guide to its 

lowest position.

4. Loosen the blade tension setting 

knob until the saw blade has 
slackened.

5. Remove the saw blade from the 

machine.

6. Fit a fresh saw blade, passing it 

behind the side guard and 
aligning it with the upper and 
lower blade guides. Centre the 
blade on the rubber tyres of the 
wheels. Ensure the teeth are 
pointing downwards towards the 
table.

WARNING: ALWAYS SWITCH OFF THE MACHINE AND DISCONNECT FROM 
THE POWER SUPPLY BEFORE CARRYING OUT ANY CLEANING OR 
MAINTENANCE TASKS.

WARNING:  THE TEETH OF THE BLADE ARE SHARP. TAKE CARE WHEN 
HANDLING THE BLADE IN SITUATIONS SUCH AS UNPACKING, MOUNTING 
OR REPLACING.

Содержание 6460072

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды