Clark Synthesis TACTILE SOUND AQ339 Aquasonic Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 20

background image

www.clarksynthesis.com

Diluvio

™

Underwater Speaker

9

Loosen the nut on the wire clamp. With the mounting gasket facing up, place the wire clamp over

the speaker. The screw & nut should be facing down towards the speaker not the sound lens.

Place the speaker on a non-abrasive surface with the sound lens facing up. Hold the face ring

above the sound lens, allowing the clamp tabs to fall open. Set the face ring against the mounting

gasket, insuring each clamp tab is on the outside of the mounting gasket. While placing the face

ring on the gasket tuck the gasket in so no red shows. Hold the entire assembly together and flip

it over, place it on the non-abrasive surface as shown in the third picture below. Carefully position

the face ring so it is centered over the sound lens.

Nut

Wire Clamp

NOTE: If using the Stainless Steel Screen, install now. See page 13 for Screen Installation.

IN-WALL INSTALLATION

3

4

«
...
7
8
9
10
11
...
»

Содержание TACTILE SOUND AQ339 Aquasonic





















Отзывы:

Нет отзывов

Похожие инструкции для TACTILE SOUND AQ339 Aquasonic

Бренд: Parasound Страницы: 16

Бренд: L-Acoustics Страницы: 46

Бренд: L-Acoustics Страницы: 24

VIV Six Five Series

Бренд: Memphis Страницы: 16

Бренд: Teac Страницы: 60

Бренд: NAD Страницы: 11

Бренд: EarthQuake Страницы: 20

The Spell Booster

Бренд: Olsson Страницы: 12

Бренд: Elektor Страницы: 48

Бренд: Audio Note Страницы: 16

Бренд: Blaupunkt Страницы: 22

Бренд: Harman Kardon Страницы: 38

Бренд: Fenton Страницы: 16

Бренд: Velleman Страницы: 30

SMARTSTEP A Series

Бренд: Omron Страницы: 251

Бренд: ValveTrain Amplification Страницы: 7

Бренд: T+A Страницы: 28

Бренд: Jung Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды