Clarion VRX815, Руководство по обслуживанию

Страница: 3 / 38

VRX815
VRX815P
- 3 -
9-2. Actuator
The actuator has a powerful magnetic circuit. If a
magnetic material is put close to it. Its characteris-
tics will change. Ensure that no foreign substances
enter through the ventilation slots in the cover.
9-3. Cleaning the lens
Dust on the optical lens affects performance. To
clean the lens, apply a small amount of isopropyl
alcohol to lens paper and wipe the lens gently.
■
SYSTEM CHECK
※
The confirmation of connected equipment must be per-
formed for this unit only when the wiring connection is
complete and power is turned on to the unit first.When
the power is supplied,"SYSTEM" and "PUSH PWR" ap-
pear alternately in the display.Press the FUNC button,the
system check starts inside the unit.When "COMPLETE"
appears,press once again the FUNC button.
■
ERROR DISPLAYS
If an error occurs,one of the following displays is displayed.Take the measures described below to eliminate the problem.
CD
CD
changer
MD
changer
Error display
ERROR 2
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR H
EEROR 2
ERROR 3
ERROR 6
Cause
A CD is caught inside the CD deck and is not ejected.
A CD cannot be played due to scratches,etc.
A CD is loaded upside-down inside the CD deck and
does not play.
A CD inside the CD changer is not loaded.
A CD inside the CD changer cannot be played due to
scratches,etc.
A CD inside the CD changer cannot be played because
it is loaded upside-down.
Displayed when the temperature in the MD changer is
too high and playback has been stopped automatically.
An MD inside the MD changer is not loaded.
An MD inside the MD changer cannot be played due to
scratches,etc.
An MD inside the MD changer cannot be played because
it is loaded upside-down.
Displayed when a non-recorded MD is loaded in the MD
changer. Measure
This is a failure of CD deck's mechanism.
Replace with a non-scratched,non-warped disc.
Eject the disc then reload it properly.
This is a failure of CD changer's mechanism.
Replace with a non-scratched,non-warped disc.
Eject the disc then reload it properly.
Lower the surrounding temperature and wait for
a while to cool off MD changer.
This is a failure of MD changer's mechanism.
Replace with a non-scratched,non-warped disc.
Eject the disc then reload it properly.
Load a pre-recorded MD in the MD changer.
Note:If an error display other than the ones described above appears, press the reset button.
■
TROUBLESHOOTING
Problem
Nothing happens when
buttons are pressd.
Display is not accurate.
Cause
The microprocessor has mal-
function due to noise,etc.
Measure
Turn off the power,then press the RELEASE lever and re-
move the DCP.Press the Reset button for about 2 seconds
with a thin rod.
Tuner Amp Unit Main Unit
The Reset button
The Reset button
■
CLOCK ADJUSTMENT
1. When the panel is open,press the [ADJ] button to select
the adjustment mode.
2. Touch the [
▼
] key to select "CLOCK".Touch the [CLOCK]
key to adjust the time.
3. Touch the [
▲
],[
▼
],[a.m] or [p.m] key to adjust the time.
※
The time is displayed in 12-hour format.
4. Press the [ADJ] button again or touch the [RTN] key two
times.The unit returns to the previous mode.
■
CHANGING THE RECEPTION AREA
This unit is initially set to USA(set to outside USA) frequency
intervals of 10kHz(9kHz) for AM and 200kHz(50kHz) for FM.
When using it outside the USA(in the USA),the frequency
reception range can be switched to the intervals below.
NOTE:( )VRX815P
SETTING THE RECEPTION AREA
While pressing [DISP] button, each time you press and hold
the number "6" of the [DIRECT] buttons for 2 seconds or
longer, the reception area switches from inside the USA to
outside the USA or from outside the USA to inside the USA.
※
Any station preset memories are lost when the recep-
tion area is changed.