Clarion VRX815, Руководство по обслуживанию

Страница: 14 / 38

VRX815
VRX815P
- 14 -
N o . 4
N o . 5 0
F i g u r e D
R i b
D r i v e m o t o r
a s s ' y
D r i v e m o t o r
a n g l e
S p i n d l e c o v e r
G r o o v e
N o t e s f o r a s s e m b l i n g
B e s u r e t o f i t t h e d r i v e m o t o r
a n g l e ( N o . 5 0 ) c o r r e c t l y i n t o
t h e r i b o f t h e s p i n d l e m o t o r
c o v e r .
N o . 1
N o . 1 9
F i g u r e E
H o l d e r
P i c k u p
L e a d s c r e w
Installation of optical pickup (Figures F, G, G-1,
and G2)
1. Apply grease to the area indicated with "xxx" on the lead
screw. (Figure F)
2. Insert the lead screw into the optical pickup. (Figure F)
3. Fasten holder No. 1 using screw No. 19. (Figure F)
4. Fit the optical pickup into the groove of the traverse as-
sembly. (Figures G and G-1)
5. Fit the lead screw into the hole. (Figure G-2)
N o . 1
N o . 1 9
F i g u r e F
H o l d e r
P i c k u p
L e a d s c r e w
N o . 1 7
F i g u r e G
P i c k u p
F i g u r e G - 1
S p r i n g
P i c k u p
T r a v e r s e a s s ' y
L e a d s c r e w
H o l e
F i g u r e G - 2
Notes for disassembling and reassembling gears
Disassembly (Figure A-1)
1. Do not remove the parts indicated with circled P-U. (Fig-
ure A-1)
※
Do not remove parts S (No.44 R-side arm) and T (No.33
temporary fastening screw for gear fixing plate). Part S
(No.44 R-side arm), once removed, cannot be reused
because its retaining pawl will crack. Using a once re-
moved R-side arm can cause unstable loading. Be sure
to replace it with a new one.
※
Replacing the rubber roller is unnecessary. Clean and
reuse it.
Reassembly (Figures A-1 and A-2)
1. Install the parts in the order of A-N. (Figure A-1)
2. Attach part E (No.40 switching lever) at the position in-
dicated with "a", then rotate it counterclockwise until it
comes to the position indicated with "b". (Figure A-2)
3. Insert the boss of part O (No.34 gear fixing plate) into
the support of each gear.
※
Make sure that the ribs of parts I (No.41 roller stopping
lever) and J (No.43 loading hook) are fitted into the in-
ner groove of part P (No.57 control slider). (Figure A-1)
※
Do not press hard on part T (No.33 temporary fastening
screw for gear fixing plate) as it can cause unstable load-
ing. Do not remove part T (No.33 temporary fastening
screw for gear fixing plate).
A
B
C
0 m m
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
F i g u r e A - 1
T h e p a r t s i n d i c a t e d w i t h c a n n o t b e
r e u s e d o n c e r e m o v e d .