background image

 

 
 
 
 
 
 
 

Q: There are cracks on the inside finish of the fabric of my shelter. Is this normal? Can anything 
be done to fix this? 

A: It is normal for some of the dark colored coating to come off the inside of the tent, particularity on a 
non-thermal tent. Over time, as you set up and take down the shelter, the dark coating can begin to 
flake off, especially along the folds in the fabric when the shelter is collapsed. This does not affect the 
function of the fabric. If you feel that too much light is now entering your shelter in the places where 
some of the coating has come off, you may wish to apply a new layer of rubberized coating. A thin 
layer of Loctite Color Guard (black), found online or at home improvement stores, works well. 
 

Q: Would it be best to completely dry out my shelter after every time it gets used? 

A: It is recommended your tent be dried out completely after each use. If it is not dried out, moisture 
may cause some damage to the shelter. This is especially important if the shelter is being stored for a 
long period of time. 
 

Q: What will help keep mice or rodents from eating the tent of my Fish Trap? 

A: We recommend keeping your tent in a sealed plastic tote with laundry dryer sheets or moth balls. If 
the shelter is stored in a barn or shed, take the tent off and store it in a more rodent-free environment. 
 

Q: How do I wash the tent of my ice fishing shelter? 

A: We recommend using a mild bleach and water solution (1 part bleach to 10 parts water), or a mild 
soap detergent and water solution to help get rid of mildew and odor in your tent. Be sure to dry the tent 
thoroughly. We do not recommend using a washing machine to clean the tent as it may cause damage. 
 

Q: Will using a heater help to eliminate or reduce water vapor and condensation in my shelter? 

A: No. A byproduct of burning propane is water. A bigger heater will produce more water vapor. Also, 
the colder the temperature outside the more condensation there will be inside the unit. 
 

Q: Are patch kits available and how do I apply them to my shelter? 

A: Yes, patch kits are available for purchase on our website. When applying a patch, it works best to 
spray adhesive (we recommend using 3M #77 or 3M #90 spray adhesive) on to both surfaces - the part 
of the tent where the patch is going to be applied and the patch itself. Wait until the adhesive begins to 
dry and becomes tacky, then place the patch on the tent. Make sure to apply the patch evenly and 
smoothly since wrinkles or uneven areas will be very difficult to correct once the two surfaces with the 
adhesive come into contact with each other. 
 

Q : Do you ship outside of the United States? 

A: We can ship to Canada, but note that all prices on our website are listed in US dollars. Canadian orders will 
include the cost of the item plus shipping, taxes & duties. 
 

 

 
 

 

 

Содержание 116611


















Отзывы: