background image

16

Installation instructions & user manual

 

9120-34373 v4.00 Nov 2018 - ZIP DBX DEX

Technical support 

 

Tel: 0345 6 005 005 email: [email protected]  www.zipwater.co.uk

COMMISSIONING

Fig. 14

Lock level

The operating mode of the appliance can be restricted.

Activation of the Lock level

•  Disconnect the appliance from the power supply.
•  Insert the jumper on the power electronics (see Fig. 14).
•  Reconnect the power supply to the appliance.

Deactivation of the Lock level

•  Disconnect the appliance from the power supply.
•  Remove jumper.
•  Reconnect the power supply to the appliance.

SERVICE MENU

The service menu offers an overview of system parameters and 

is used for diagnostics.  

•  Press key   and key   simultaneously for at least 2 seconds to 

call up the service menu, the display confirms by “FL” and by a 

flashing point. Use the arrow keys   and  , to switch between 

the individual menu items.

•  Press key   to see the value of the currently selected menu. The 

value flashes in the display. (The values of some menus can be 

switched over by using the arrow keys   and  .) Return to the 

drop-down-menu by pressing key   again. With key   return to 

the standard display (nominal value). After two minutes without 

any key stroke the system automatically switches back to the 

standard display.

2

8

4

7

5

3

6

9

+

1

Open service menu

Display flashes

Press

≥ 2 sec

Содержание Zip InLine DBX Series

























Отзывы: