21
20
23
22
6. Device Configuration
7.Group Device
6.2.2 Configuration
To configure a new CG100 device, perform following steps.
1 - Power up the new CG100 device.
2 - Connect the Wireless remote controller
(which is used to configure the Coordinator
before) to the new device through the
provided cable.
3 - Press the navigation button to enter Menu,
then select "Dev. Manager" and go to
"Config Device".
4 - Press "Yes" button to configure the new
device.
(Note: The icon is indicating the new
device is trying to connect to the network).
5 - If the device is configured successfully, the
wireless remote controller will show "Config
Device Success".
During the configuration of new device,
if "Fail" or "Device Not Found" is shown by
wireless remote controller, please check the
power of the new device and the connection
between the new device and wireless
remote controller. Then perform step 1 to
step 4 again.
Repeat steps stated in Section 6.2.1 and Section 6.2.2 to install the rest
of the devices
7.Group Device
6. Device Configuration
6.3 Wireless Remote Controller
During the configuration of coordinator, the wireless remote controller will be self-configured
automatically. User may use such wireless remote controller to configure other new device in
the network. On the other hand, when there are more than one wireless remote controller
within the system, user shall configure the other wireless remote controller (which are not used
to configure coordinator) manually before using the wireless remote controller. To configure
the handheld remote manually, perform following steps.
1 -Connect the new wireless remote controller to any
successful configured CG100 Coordinator/device
through the provided cable.
2 -Press the navigation button to enter Menu, then
select "Dev. Manager" and go to "Config Remote".
3 -Press "Yes" button to configure the wireless remote
controller.
4 -When the wireless remote controller is configured
successfully, the wireless remote controller will show
"Config Remote Success'.
During the configuration of wireless remote controller,
if "Fail" or "Device Not Found" is shown by the wireless
remote controller, please check the power of the
Coordinator/device and the connection between the
Coordinator/device and wireless remote controller. Then
perform step 1 to step 3 again
After the CG100 devices are installed and configured, user may assign a corresponding
button (1-10) on Wireless remote controller to control one or more devices (maximum three),
which is called group control. The procedures of adding device to a group and controlling
grouped devices are illustrated in Section 7.1 and Section 7.2 - 7.3 respectively.
7.1
Add Device to Group
To add device to group control, perform following steps.
1 -Connect the Wireless remote controller
(which is configured before) to the desired device
(eg. One-gang Switch, Two-gang Switch, Dimmer
Switch, Socket, etc.) through the provided cable.
2 -Press the "Navigation" button to enter Menu, then
select "Group Config".
(Note: All the groups will show on the screen, user
may scroll to view the groups.)
(Note: If there is/are device(s) added to the group,
the Wireless remote controller will show the name of the
group. eg. The default group name of the first
group is "Group 1".)
(Note: If there is no device added to the group, the
Handheld will show "(Empty)".)
3 -Press "Yes" button to select the desired group.
(Note: If there is no device added to the group, the
Handheld remote will show "No Device".)
(Note: If there is/are device(s) added to the group,
the Wireless remote controller will show the name of the
device.)
4 -Scroll down to find "Add Device"
(Note: If there are three devices already added to
the group, the "Add Device" function will be
disabled and user may not found such function
within the group.)
5 -Press "Yes" button to add device
The Wireless remote controller will show
"Press Desired Device", and the status LED of
connected device will keep flashing.
6 -Press the desired device control button on the
device to add the device to the group.
For example, when the Wireless remote controller is
connecting with the Two-gang Switch and user press
the second button of the switch, the device control
function of the second button of the switch will be
added to the group.
7 -When the device is added to the group successfully,
the Wireless remote controller will show "Add Device Success"
If "Fail" or "Device Not Found" is shown on the Wireless
remote controller during the above process, please check the
power of the Coordinator/device and the connection
between the Coordinator/device and Wireless remote controller.
And you can also check the memory information of
Wireless remote controller(see Section 9.4). Then perform
step 1 to step 6 again.
7.2 On/OFF Control
After the devices are added to different groups, user may control the group of device(s)
through a single button (1 - 10 buttons) on the Wireless remote controller.
Important: Please ensure the wireless remote controller is within the system coverage
before controlling any device.
Following examples show the procedures to control a group of device.
Press and hold the "Back" button to exit the menu and show the device status page.
From the above example of device status page:
Group 1: Device(s) is/are HALF ON
Group 2: No device in Group 2
Group 3: Device(s) is/are ON
Group 4: Device(s) is/are OFF
Group 5: Device(s) is/are OFF
