manualshive.com logo in svg

Cisco UCS C200, Инструкция по установке и обслуживанию

Поделиться
Скачать
Cisco UCS C200 Скачать руководство пользователя страница 46

   

3-6

Cisco UCS C200 Server Installation and Service Guide

OL-20732-02

Chapter 3      Maintaining the Server

  Status LEDs

Note

The 10/100/1000 Gigabit Ethernet link status LED and the speed LED must be 
read in combination for the following interpretations.

10/100/1000 Gigabit 
Ethernet speed (left)

10/100/1000 Gigabit 
Ethernet link status (right)

  •

Link status off + speed off—No link is present on this port.

  •

Link status off + speed solid green—A half-duplex, 10-Mbps link 
is present.

  •

Link status green + speed solid green—A half-duplex, 100-Mbps 
link is present.

  •

Link status amber + speed solid green—A half-duplex, 1000-Mbps 
link is present.

  •

Link status off + speed blinking green—A full-duplex, 

 

10-Mbps link is present.

  •

Link status green + speed blinking green—A full-duplex, 
100-Mbps link is present.

  •

Link status amber + speed blinking green—A full-duplex, 
1000-Mbps link is present.

Table 3-2

Rear Panel LEDs  (continued)

LED Name

State

Содержание UCS C200













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды