manualshive.com logo in svg

Cisco UCS C200, Инструкция по установке и обслуживанию

Поделиться
Скачать
Cisco UCS C200 Скачать руководство пользователя страница 19

   

1-5

Cisco UCS C200 Server Installation and Service Guide

OL-20732-02

Chapter 1      Overview

Disk 
Management

Factory-configured RAID

9

 support options, which differ for the LFF and SFF 

versions of the server.

  •

LFF:

  –

RAID 0 and 1 support for up to 4 SATA drives with the integrated SATA 
controller.

Note

The integrated ICH10R RAID controller is not compatible for use with 
VMWare ESX/ESXi Server software in any generation or version of the 
Cisco UCS C200 server.

  –

RAID 0, 1, and 1E support for up to 4 SAS or SATA drives with the optional 
LSI 1064-based controller mezzanine card.

  –

RAID 0, 1, 5, 6, 00, 10, 50 and 60 support for up to 4 SAS or SATA drives 
with the optional LSI 9260-8i MegaRAID controller card.

  •

SFF:

  –

RAID 0 and 1 support for up to 4 SATA drives with the integrated SATA 
controller.

Note

The integrated ICH10R RAID controller is not compatible for use with 
VMWare ESX/ESXi Server software in any generation or version of the 
Cisco UCS C200 server.

  –

RAID 0, 1, and 1E support for up to 4 SAS or SATA drives with the optional 
LSI 1068-based controller mezzanine card.

  –

RAID 0, 1, 5, 6, 00, 10, 50 and 60 support for up to 8 SAS or SATA drives 
with the optional LSI 9260-8i MegaRAID controller card.

  –

RAID 0, 1, 5, 6, 00, 10, 50 and 60 support for up to 4 SAS or SATA drives 
with the optional LSI 9280-4i4e MegaRAID controller card.

See 

RAID Controller Considerations, page C-1

 for more information about RAID in 

this server.

Video

The server CIMC chip includes a Matrox G200 core. The Matrox G200 core shares 
the same memory as the rest of the CIMC. The first 8 MB of memory are allocated 
to the video core, followed by another 5 MB allocated to the compression engine for 
difference buffers.

1.

DIMM = dual inline memory module

2.

DDR = double data rate (transfer mode)

3.

SAS = serial attached SCSI

4.

SATA = serial advanced technology attachment 

5.

VGA = video graphics array

6.

USB = universal serial bus

7.

KVM = keyboard, video, mouse

8.

PCIe = peripheral component interconnect express

Table 1-1

Hardware Features of the Server  (continued)

Feature or 
Component

Cisco UCS 

C200

 Server

Содержание UCS C200













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды