manualshive.com logo in svg

Cisco UCS C200, Инструкция по установке и обслуживанию

Поделиться
Скачать
Cisco UCS C200 Скачать руководство пользователя страница 23

   

2-3

Cisco UCS C200 Server Installation and Service Guide

OL-20732-02

Chapter 2      Installing the Server

  Preparing for Installation

Preparing for Installation 

This section includes the following topics:

  •

Installation Guidelines, page 2-3

  •

Rack Requirements, page 2-4

  •

Required Equipment, page 2-4

Installation Guidelines 

Warning

To prevent the system from overheating, do not operate it in an area that exceeds the maximum 
recommended ambient temperature of: 35° C (95° F).

 

Statement 1047

Warning

The plug-socket combination must be accessible at all times, because it serves as the main 
disconnecting device.

 

Statement 1019

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that 
the protective device is rated not greater than: 250 V, 15 A.

 

Statement 1005

Warning

Installation of the equipment must comply with local and national electrical codes.

 

Statement 1074

When installing the server, follow these guidelines:

  •

Plan your site configuration and prepare the site before installing the server. See the 

Cisco UCS Site 

Preparation Guide 

for the recommended site planning tasks.

  •

Ensure that there is adequate space around the server to allow for servicing and for adequate airflow. 
The airflow in this server is from front to back.

  •

Ensure that the air-conditioning meets the thermal requirements listed in 

Appendix A, “Technical 

Specifications.”

  •

Ensure that the cabinet or rack meets the requirements listed in the 

“Rack Requirements” section on 

page 2-4

.

  •

Ensure that the site power meets the power requirements listed in 

Appendix A, “Technical 

Specifications.”

 If available, you can use an uninterruptible power supply (UPS) to protect against 

power failures. 

Caution

Avoid UPS types that use ferroresonant technology. These UPS types can become unstable with systems 
such as the Cisco UCS, which can have substantial current draw fluctuations from fluctuating data traffic 
patterns.

Содержание UCS C200













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды