background image

S e n d   d o c u m e n t   c o m m e n t s   t o   u c s - d o c f e e d b a c k @ c i s c o . c o m

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco UCS B200 Blade Server Installation and 
Service Note

The UCS B200 blade server (shown in 

Figure 1

) is now only available in the M2 version (the M1 version 

is no longer sold as of 1/21/2011). The procedures in this document apply to both versions. The Cisco 
UCS B200 is a half-width blade with 12 DIMM slots; it supports one adapter. You may install up to eight 
UCS B200 Blade Servers to a UCS chassis.

Figure 1

Cisco UCS B200 Front Panel

1

Asset tab 

1

1.

Each server has a blank plastic tag that pulls out of the front panel, provided so you can add your 
own asset tracking label without interfering with the intended air flow. 

7

Network link status LED

2

Blade ejector handle

8

Blade health LED

3

Ejector captive screw

9

Console connector

4

Hard drive bay 1

10

Reset button access

5

Hard drive bay 2

11

Beaconing LED and button

6

Power button and LED

195354

4

5

1

2

3

6

7

8

9

10

11

Содержание UCS B200































Отзывы: