Cisco UCS B200 Скачать руководство пользователя страница 10

Страница: 10 / 30

S e n d d o c u m e n t c o m m e n t s t o u c s - d o c f e e d b a c k @ c i s c o . c o m

Cisco UCS B200 Blade Server Installation and Service Note

OL-22473-02

Installing and Removing a Blade Server Hard Drive

Table 2

shows the drives supported in this blade server.

Removing a Blade Server Hard Drive

To remove a hard drive from a blade server, follow these steps:

Step 1

Push the button to release the ejector, and then pull the hard drive from its slot.

Table 2

Supported Hard Disk Drives (HDD)

Product ID

Description

HDD

A03-D073GC2

This part reached end of sale on 12/12/2011.

73 GB, 6Gb SAS transfer rate

, 15K RPM HDD/hot plug/drive sled mounted

The built-in 1064E RAID controller runs at 1.5Gb Link Speed instead of 3Gb with 6Gb Local Disks when running UCS 1.4(2) and earlier software
eleases.

A03-D146GA2

This part reached end of sale on 12/16/2011.

146 GB 6Gb SAS transfer rate

, 10K RPM SFF HDD/hot plug/drive sled mounted

A03-D146GC2

146 GB 6Gb SAS transfer rate

, 10K RPM SFF HDD/hot plug/drive sled mounted

A03-D300GA2

300 GB, 6Gb SAS transfer rate

, 10K RPM HDD/hot plug/drive sled mounted

A03-D600GA2

600 GB, 6Gb SAS transfer rate

, 10K RPM HDD/hot plug/drive sled mounted

A03-D1TBSATA

1TB 6Gb SATA 7.2K RPM SFF HDD/hot plug/drive sled mounted

A03-D500GC3

500GB 6Gb SATA 7.2K RPM SFF hot plug/drive sled mounted

UCS-HDD300GI2F105

300GB 6Gb SAS 15K RPM SFF HDD/hot plug/drive sled mounted

UCS-HDD900GI2F106

900GB 6Gb SAS 10K RPM SFF HDD/hot plug/drive sled mounted

This drive requires UCS capability catalog version 1.0.54.T or 2.0.1pT or later.

SSD

UCS-SSD100GI1F104

100GB SATA SSD SFF

This drive requires UCS capability catalog version 1.0.50.T or 2.0.1nT or later.

A03-D100SSD

100 GB SATA SSD HDD/hot plug/drive sled mounted

Содержание UCS B200































Результаты поиска

Содержание UCS B200

Отзывы:

Похожие инструкции для UCS B200

Бренды по названию

Популярные бренды

Cisco UCS B200, Инструкция по установке и обслуживанию

Результаты поиска

Содержание UCS B200

Отзывы:

Похожие инструкции для UCS B200

Бренды по названию

Популярные бренды