Cisco SN 5428-2 Скачать руководство пользователя страница 33

Страница: 33 / 78

2-7

Cisco SN 5428-2 Storage Router Hardware Installation Guide

OL-4797-01

Chapter 2 Installing the SN 5428-2 Storage Router

Installing the SN 5428-2 Chassis

Rack-Mounting the SN 5428-2 Storage Router

You can rack-mount the SN 5428-2 Storage Router chassis in a 19-inch
equipment rack with the front panel forward.

You need the following tools to install the storage router in a rack:

•

#2 Phillips screwdriver

•

Tape measure

To install the storage router in a rack, follow these steps:

Step 1

Locate the following rack-mount components in the accessory kit shipped with
your storage router:

•

Two mounting brackets labeled RIGHT and LEFT. (See

Figure 1

•

Two sets of rack rails. Each set consists of a rail labeled FRONT and a rail
labeled REAR. (See

Figure 2

•

Two cable guides (with black mounting screws).

•

Assorted screws and fasteners (use as needed).

Figure 1

Mounting Brackets

85500

Left

Right

Содержание SN 5428-2















































































Результаты поиска

Содержание SN 5428-2

Отзывы:

Похожие инструкции для SN 5428-2

Бренды по названию

Популярные бренды

Cisco SN 5428-2, Руководство по установке оборудования

Результаты поиска

Содержание SN 5428-2

Отзывы:

Похожие инструкции для SN 5428-2

Бренды по названию

Популярные бренды