manualshive.com logo in svg

Cisco PA-2CT1, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-2CT1 Скачать руководство пользователя страница 9

Channelized T1 Port Adapter Installation and Configuration  9

Port Adapter Locations on the VIP2 and in Cisco 7200 Series Routers

Figure 3

Two Port Adapters on a VIP2-50 (Horizontal Orientation Shown)

Note

In the Cisco 7000, Cisco 7507, and Cisco 7513 chassis, the VIP2 is installed vertically. In the

Cisco 7010 and Cisco 7505 chassis, the VIP2 is installed horizontally.

In Cisco 7200 series routers, port adapter slots are numbered from the lower left to the upper right,
beginning with port adapter slot 1 and continuing through port adapter slot 2 for the Cisco 7202,
slot 4 for the Cisco 7204 and Cisco 7204VXR, and slot 6 for the Cisco 7206 and Cisco 7206VXR.
Port adapter slot 0 is reserved for the optional Fast Ethernet port on the I/O controller—if present.

Note

The I/O controller is available with or without a Fast Ethernet port. You can install both I/O

controller types in all Cisco 7200 series routers; however, when you install an I/O controller with a
Fast Ethernet port in a Cisco 7202, the system software automatically disables the port.

Figure 4 shows a Cisco 7206 with installed port adapters and an I/O controller with a Fast Ethernet
port. Not shown are the Cisco 7202, which has two port adapter slots, the Cisco 7204 and
Cisco 7204VXR, which have four port adapter slots, and the Cisco 7206VXR, which has six port
adapter slots. The 2CT1 port adapter can be installed in any available port adapter slot in Cisco 7200
series routers.

Bus connector

SRAM 

daughter

card

Port adapter 

in slot 0

Port
adapter 
in slot 1

DRAM DIMM

H10447

CPU

Boot ROM

Содержание PA-2CT1























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды