manualshive.com logo in svg

Cisco PA-2CT1, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-2CT1 Скачать руководство пользователя страница 36

36 Channelized T1 Port Adapter Installation and Configuration

Cisco 7200 Series and the 2CT1 Port Adapter

Step 5

With the port adapter halfway in the slot, connect all required cables to the port adapter.

Step 6

After connecting all required cables, carefully slide the port adapter all the way into the
slot until you feel the port adapter’s connectors make contact with the midplane.

Step 7

After feeling the connectors make contact, move the port adapter lever to the locked
position. Figure 19 shows the port adapter lever in the locked position.

Note

If the port adapter lever does not move to the locked position, the port adapter is

not completely seated in the midplane. Carefully pull the port adapter halfway out of the
slot, reinsert it, and move the port adapter lever to the locked position.

Figure 19

Placing the Port Adapter Lever in the Locked Position (Cisco 7206 Shown)

This completes the procedure for installing a new port adapter in a Cisco 7200 series router.

Attaching a 2CT1 Interface Cable

On a single 2CT1 port adapter, you can use up to two serial connections.

Use the following procedure to connect a 2CT1 interface cable:

Step 1

Attach the cable directly to the receptacle on the 2CT1 port adapter and tighten the
strain-relief screws. (See Figure 20.)

Note

Port adapters have a handle attached, but this handle is not shown to allow a

detailed view of each port adapter’s faceplate.

ETHERNET 10BT

ENABLED

0

2

1

3

LINK

0

1

2

3

FAST SERIAL

EN

TD

TC

RD

RC

LB CD

TD

TC

RD

RC

LB CD

TD

TC

RD

RC

LB CD

TD

TC

RD

RC

LB CD

ENABLED

MII

LINK

RJ45

FAST ETHERNET 

0

TOKEN RING

0

1

2

3

0

2

4

1

3

5

6

H6747

MII

EN

RJ45

EN

RJ45

LINK

1O PWR

OK

RJ-45

CPU RESET

FAST ETHERNET INPUT/OUTPUT CONTROLLER

ENABLED

PCMCIA

EJECT

SLOT 0

SLOT 1

FE MII

Port adapter

handle

Port adapter

lever (locked

position)

Note: This adapter installation
applies to any port or service
adapter.

Содержание PA-2CT1























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды