manualshive.com logo in svg

Cisco PA-2CT1, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-2CT1 Скачать руководство пользователя страница 16

16 Channelized T1 Port Adapter Installation and Configuration

VIP2 and the 2CT1 Port Adapter

Step 10

Before you insert the new port adapter in its slot, verify that the port adapter carrier is
between the upper and lower slot edges, as shown in Figure 10. Do not jam the carrier
between the slot edges.

Caution

To ensure a positive ground attachment between the port adapter carrier and the VIP2

motherboard and port adapter slot, and to ensure that the connectors at the rear of the port adapter
and slot seat properly, make certain the carrier is between the upper and lower slot edges, as shown
in Figure 11.

Step 11

Carefully slide the new port adapter into the port adapter slot until the connector on the
port adapter is completely seated in the connector on the motherboard.

Figure 12

Aligning the Carrier Edge with Upper and Lower Slot Edges (Partial View)

Step 12

Install the screw in the rear of the port adapter slot. (See Figure 9 for its location.) Do not
overtighten this screw.

Step 13

To replace the VIP2 in the chassis, follow the steps in the section “Installing a VIP2” in
the configuration note Second-Generation Versatile Interface Processor (VIP2)
Installation and Configuration, which shipped with your VIP2.

Step 14

Reconnect the interface cables to the interface processor.

This completes the procedure for installing a new port adapter or replacing a port adapter on a VIP2.

H3152 

Содержание PA-2CT1























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды