manualshive.com logo in svg

Cisco PA-2CT1, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-2CT1 Скачать руководство пользователя страница 19

Channelized T1 Port Adapter Installation and Configuration  19

Configuring 2CT1 Interfaces

Table 5

ISDN Service Provider Switch Types

For complete descriptions of interface commands and the configuration options available for
Cisco 7000 series and Cisco 7500 series-related interfaces, refer to the publications listed in the
“Related Documentation” section on page 2.

Selecting Chassis Slot, Port Adapter, and Port Adapter Port Numbers

This section describes how to identify chassis slot, port adapter, and 2CT1 port adapter interface
numbers.

Note

Although the processor slots in the 7-slot Cisco 7000, Cisco 7507, and 13-slot Cisco 7513 are

vertically oriented and those in the 5-slot Cisco 7010 and Cisco 7505 are horizontally oriented, all
models use the same method for slot and port numbering.

In the router, physical port addresses specify the actual physical location of each interface port on
the port adapter end. (See Figure 14.) This address is composed of a three-part number in the format
chassis slot number/port adapter number/interface port number.

•

The first number identifies the chassis slot in which the VIP2 is installed (as shown in the sample
system in Figure 14).

•

The second number identifies the physical port adapter number on the VIP2, and is either 0 or 1.

•

The third number identifies the interface ports on each 2CT1 port adapter, which are always
numbered in sequence as interface 0 through 1.

Keywords by Area

Switch Type

Australia

basic-ts013

Australian TS013 switches

Europe

basic-1tr6
basic-nwnet3
basic-net3

basic-net5
primary-net5
vn2
vn3

German 1TR6 ISDN switches
Norwegian NET3 ISDN switches (phase 1)
NET3 ISDN switches (UK, Denmark, and other nations);

covers the Euro-ISDN E-DSSI signaling system)

NET5 switches (UK and Europe)
European ISDN PRI switches (UK and Europe)
French VN2 ISDN switches
French VN3 ISDN switches

Japan

ntt
primary-ntt

Japanese NTT ISDN switches
Japanese ISDN PRI switches

North America

basic-5ess
basic-dms100
basic-ni1
primary-4ess
primary-5ess
primary-dms100

AT&T basic rate switches
NT DMS-100 basic rate switches
National (North American) ISDN-1 switches
AT&T 4ESS switch type for the U.S. (ISDN PRI only)
AT&T 5ESS switch type for the U.S. (ISDN PRI only)
NT DMS-100 switch type for the U.S. (ISDN PRI only)

New Zealand

basic-nznet3

New Zealand NET3 switches

Содержание PA-2CT1























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды