Cisco Nexus 5600 Series Скачать руководство пользователя страница 176

Страница: 176 / 480

172

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

Chapter I Commands

ip igmp static-oif

To statically bind a multicast group to the outgoing interface (OIF), which is handled by the device
hardware, use the

ip igmp static-oif

command. To remove a static group, use the

form of this

command.

ip igmp static-oif

{

group

[

source

source

] |

route-map

policy-name

}

no ip igmp static-oif

{

group

[

source

source

] |

route-map

policy-name

}

Syntax Description

Command Default

None

Command Modes

Interface configuration mode

Supported User Roles

network-admin
vdc-admin

Command History

Usage Guidelines

Before you use this command, make sure that you enable Protocol Independent Multicast (PIM) on the
interface by using the

ip pim sparse-mode

command.

This command does not require a license.

Examples

This example shows how to statically bind a group to the OIF:

switch(config)#

interface ethernet 2/2

switch(config-if)#

no switchport

switch(config-if)#

ip igmp static-oif 230.0.0.0

switch(config-if)#

This example shows how to remove a static binding from the OIF:

switch(config)#

interface ethernet 2/2

group

Multicast group IPv4 address. If you specify only the group address, the (*, G) state
is created.

source

source

(Optional) Configures the source IP address for IGMPv3 and creates the (S, G) state.

Note

A source tree is built for the (S, G) state only if you enable IGMPv3.

route-map

policy-name

Specifies the route-map policy name that defines the group prefixes where this
feature is applied. The route map name can be a maximum of 63 alphanumeric
characters.

Release

Modification

6.0(2)N1(1)

This command was introduced.

Содержание Nexus 5600 Series

































































































































































































































































































































































































































































































Результаты поиска

Содержание Nexus 5600 Series

Отзывы:

Похожие инструкции для Nexus 5600 Series

Бренды по названию

Популярные бренды

Cisco Nexus 5600 Series, Справочник

Результаты поиска

Содержание Nexus 5600 Series

Отзывы:

Похожие инструкции для Nexus 5600 Series

Бренды по названию

Популярные бренды