Cisco NCS 5501 Скачать руководство пользователя страница 80

Страница: 80 / 82

Power Supply LEDs

NCS 55A1-24H, NCS 5501 and NCS 5501 SE Power Supply LEDs

Power modules are located on the back side of the chassis. Each NCS 55A1-24H, NCS 5501 and NCS 5501
SE power module has an OK and a FAIL LED.

Table 16: Power Supply LED Descriptions

Status

FAIL LED

OK LED

Power supply is on and outputting power to the router.

Off

Green

Power supply is connected to input power source but not outputting
power to the router. The power supply might not be properly installed
in the chassis.

Off

Flashing green

Either all of the installed power supplies are not receiving power or
an uninstalled power supply is not receiving power.

Off

Power supply is operating but a warning condition has
occurred

—

possibly one of the following conditions:

•

High temperature

•

High power

•

Slow power supply fan

•

Low voltage

•

Power supply is installed in the chassis but was disconnected
from the power source

Flashing amber

Off

Power supply failure

—

possibly one of the following conditions:

•

Over voltage

•

Over current

•

Over temperature

•

Power supply fan failure

Amber

Off

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

LEDs

Power Supply LEDs

Содержание NCS 5501



















































































Результаты поиска

Содержание NCS 5501

Отзывы:

Похожие инструкции для NCS 5501

Бренды по названию

Популярные бренды

Cisco NCS 5501, Руководство по установке оборудования

Результаты поиска

Содержание NCS 5501

Отзывы:

Похожие инструкции для NCS 5501

Бренды по названию

Популярные бренды