Cisco NCS 5501 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 82

background image

Clearance Requirements

The fixed-port chassis requires front-to-back airflow. Leave at least 6.0 in. (15.24 cm) front and rear clearance
for air intake/exhaust. Leave an additional 6.0 in. (15.24 cm) rear clearance for removal and installation of
power supplies and fan modules.

Figure 33: Clearances Required Around the Chassis

6.0 in. (15.24 cm) rear clearance for air
intake/exhaust.

4

Chassis

1

Additional 6.0 in. (15.24 cm) rear clearance for
removal and installation of power supplies and
fan modules.

5

6.0 in. (15.24 cm) front clearance for air
intake/exhaust.

2

Chassis depth

3

Weight, Quantity and Power Consumption

NCS 5501 Fixed Chassis Weight, Quantity and Power Consumption

The NCS 5501 fixed chassis offers two hot-swappable power supplies providing

1

+

1

redundancy. For

1

+

1

redundancy mode, there must be two subsystems each, providing enough power supply to maintain the system.

Table 10: NCS 5501 and NCS 5501 SE Weight, Quantity and Power Consumption

Maximum Power

Typical Power

Weight per Unit

Component

Chassis

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

62

System Specifications

Clearance Requirements

«
...
68
69
70
71
72
...
»

Содержание NCS 5501



















































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 5501

Бренд: Magnat Audio Страницы: 2

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

BroadLink SP3353

Бренд: MicroNet Страницы: 66

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: SAGEMCOM Страницы: 75

System Storage DS3200

Бренд: IBM Страницы: 2

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

Бренд: IBM Страницы: 72

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: PaloAlto Networks Страницы: 28

LinkStation 500

Бренд: Buffalo Страницы: 139

Бренд: LevelOne Страницы: 2

Бренд: DPS Telecom Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды