Cisco N9K-C9336C-FX2-E Скачать руководство пользователя страница 5

Страница: 5 / 44

C H A P T E R

Overview

•

Overview

The Cisco Nexus 9336C-FX2-E switch (N9K-C9336C-FX2-E) is a 1-rack unit (RU), fixed-port switch designed
for deployment in data centers. This switch has the following ports:

• 36 40/100-Gigabit QSFP28 ports

• Two management ports (one 10/100/1000BASE-T port and one SFP port)

• One console port (RS-232)

• One USB port

This switch includes the following user-replaceable components:

• Fan modules (6) with the following airflow choices:

• Port-side exhaust fan module with blue coloring (NXA-FAN-35CFM-PE)

• Port-side intake fan module with burgundy coloring (NXA-FAN-35CFM-PI)

• Port-side exhaust fan module with blue coloring (NXA-SFAN-35CFM-PE)

• Port-side intake fan module with burgundy coloring (NXA-SFAN-35CFM-PI)

To enable or disable displaying the serial number of the NXA-SFAN-35CFM-PI
or NXA-SFAN-35CFM-PE fan, enter the [

]

hardware fan-sprom

command.

Note

• Power supply modules (two—One for operations and one for redundancy [1+1]) with the following

choices:

• 750-W port-side exhaust AC power supply with blue coloring (NXA-PAC-750W-PE)

• 750-W port-side intake AC power supply with burgundy coloring (NXA-PAC-750W-PI)

• 1100-W port-side exhaust AC power supply with blue coloring (NXA-PAC-1100W-PE)

Cisco Nexus 9336C-FX2-E NX-OS Mode Switch Hardware Installation Guide

Содержание N9K-C9336C-FX2-E













































Результаты поиска

Содержание N9K-C9336C-FX2-E

Отзывы:

Похожие инструкции для N9K-C9336C-FX2-E

Бренды по названию

Популярные бренды

Cisco N9K-C9336C-FX2-E, Руководство по установке оборудования

Результаты поиска

Содержание N9K-C9336C-FX2-E

Отзывы:

Похожие инструкции для N9K-C9336C-FX2-E

Бренды по названию

Популярные бренды