Cisco N9K-C9336C-FX2-E Скачать руководство пользователя страница 40

Страница: 40 / 44

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Table 1: Regulatory Standards Compliance: Safety and EMC

Description

Specification

Products should comply with CE Markings according to directives 2004/108/EC
and 2006/95/EC.

Regulatory compliance

• CAN/CSA-C22.2 No. 60950-1 Second Edition

• EN 60950-1 Second Edition

• IEC 60950-1 Second Edition

• AS/NZS 60950-1

• GB4943

Safety

• 47CFR Part 15 (CFR 47) Class A

• AS/NZS CISPR22 Class A

• CISPR22 Class A

• EN55022 Class A

• ICES003 Class A

• VCCI Class A

• EN61000-3-2

• EN61000-3-3

• KN22 Class A

• CNS13438 Class A

EMC: Emissions

• EN55024

• CISPR24

• EN300386

• KN 61000-4 series

EMC: Immunity

The product is RoH-6 compliant with exceptions for leaded-ball grid-array (BGA)
balls and lead press-fit connectors.

RoHS

Cisco Nexus 9336C-FX2-E NX-OS Mode Switch Hardware Installation Guide

System Specifications

Regulatory Standards Compliance Specifications

Содержание N9K-C9336C-FX2-E













































Результаты поиска

Содержание N9K-C9336C-FX2-E

Отзывы:

Похожие инструкции для N9K-C9336C-FX2-E

Бренды по названию

Популярные бренды

Cisco N9K-C9336C-FX2-E, Руководство по установке оборудования

Результаты поиска

Содержание N9K-C9336C-FX2-E

Отзывы:

Похожие инструкции для N9K-C9336C-FX2-E

Бренды по названию

Популярные бренды