Cisco N9K-C9336C-FX2-E Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 44

background image

• The depth of a four-post rack must be 24 to 32 inches (61.0 to 81.3 cm) between the front and rear

mounting rails (for proper mounting of the bottom-support brackets or other mounting hardware).

Also, you must have power receptacles that are located within reach of the power cords that are used with the
switch.

Statement 1048—

Rack Stabilization

The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before installation
or servicing. Failure to stabilize the rack can cause bodily injury.

Warning

Cisco Nexus 9336C-FX2-E NX-OS Mode Switch Hardware Installation Guide

8

Preparing the Site

Rack and Cabinet Requirements

«
...
10
11
12
13
14
...
»

Содержание N9K-C9336C-FX2-E













































Отзывы:

Нет отзывов

Похожие инструкции для N9K-C9336C-FX2-E

Бренд: NETGEAR Страницы: 15

EG2-1600 Series

Бренд: Leonton Страницы: 19

iBootBar iBB-DC8

Бренд: Dataprobe Страницы: 36

Бренд: SMC Networks Страницы: 6

Бренд: Hama Страницы: 14

Бренд: TDT Страницы: 21

Atlona AT-HDR-SW-52ED

Бренд: Panduit Страницы: 81

Бренд: Data Video Страницы: 47

Бренд: Chauvet Страницы: 20

Бренд: Kramer Страницы: 103

Бренд: Kramer Страницы: 128

Бренд: Hitachi Страницы: 30

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды