manualshive.com logo in svg

Cisco ME-3600X-24CX Series, Руководство пользователя

Поделиться
Скачать
Cisco ME-3600X-24CX Series Скачать руководство пользователя страница 32

 

2-13

Cisco ME-3600X-24CX Series Switch Chassis Configuration Guide

OL-27620-01

Chapter 2      Configuring T1/E1 Interfaces

  Monitoring and Maintaining the T1/E1 Interface Module

Monitoring and Maintaining the T1/E1 Interface Module

After configuring the new interface, you can monitor the status and maintain the interface module by 
using show commands. To display the status of any interface, complete any of the following tasks in 
EXEC mode:

Configuring CEM

This section provides information about how to configure CEM. CEM provides a bridge between a 
time-division multiplexing (TDM) network and a packet network, such as Multiprotocol Label 
Switching (MPLS). The router encapsulates the TDM data in the MPLS packets and sends the data over 
a CEM pseudowire to the remote provider edge (PE) router. Thus, function as a physical communication 
link across the packet network.

The following sections describe how to configure CEM:

  •

Configuring a CEM Group, page 2-13

  •

Using CEM Classes, page 2-14

  •

Configuring CEM Parameters, page 2-15

Note

CEM is used as an element in configuring pseudowires including Structure-Agnostic TDM over Packet 
(SAToP) and Circuit Emulation Service over Packet-Switched Network (CESoPSN). For more 
information about configuring pseudowires, see 

Chapter 5, “Configuring Pseudowire.”

Configuring a CEM Group

The following section describes how to configure a CEM group on the Cisco ME 3600X 
24CX Series Switch.

SUMMARY STEPS

1.

enable

2.

configure terminal

3.

controller {t1 | e1} 0/number

4.

cem-group group-number {unframed | timeslots timeslot}

5.

End 

Task

Command

Display the status of the E1 or T1 controller. show controllers {e1 | t1} [0/number] [brief] 

Содержание ME-3600X-24CX Series
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды