Cisco MDS 9396T Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 68

background image

Preinstallation Guidelines

Airflow Considerations

The switch comes with fan modules and power supply units that have either port-side intake or port-side
exhaust airflow for cooling the switch. If you are orienting the switch with the FC ports facing a cold aisle,
make sure that the switch has a port-side intake fan and power supply modules with red colorings. If you are
orienting the switch with the fan and power supply modules facing a cold aisle, make sure that the switch has
port-side exhaust fan and power supply units with blue colorings. All fan modules and power-supply modules
must have the same direction of airflow.

Connection Guidelines for AC-Powered Systems

To connect to the Cisco MDS 9396T switch AC power supply units to the site power source, follow these
guidelines:

• For power redundancy, each power supply should be connected to a separate power feed (at a minimum,

separate branch circuits).

• Circuits should be sized according to local and national codes.

• The AC power receptacles that are used to power the chassis must be the grounding type. The grounding

conductors that connect to the receptacles should connect to protective earth ground in the service
equipment.

Installation Guidelines

Follow these guidelines when installing the Cisco MDS 9396T Switch:

• Plan your site configuration and prepare the site before installing the switch.

• Each new switch requires a license; see the

Cisco MDS 9000 Family NX-OS Licensing Guide

for

instructions on installing a license.

• Ensure there is adequate space around the switch to allow for servicing the switch and for adequate

airflow (airflow requirements are listed the

Technical Specifications

section).

• Ensure the air-conditioning meets the heat dissipation requirements listed the

Technical Specifications

section.

• Ensure the cabinet or rack meets the requirements listed in the

Cabinet and Rack Requirements

section.

• Ensure that the cabinet or rack meets the requirements listed in the

Cabinet and Rack Requirements

section.

If the front cabinet mounting rails are not offset from the front door or bezel panel by a minimum of 3 inch
(7.6 cm), and a minimum of 5 inch. (12.7 cm), respectively, and cable management brackets are installed on
the front of the chassis, the chassis should be mounted rear-facing to ensure the minimum bend radius for
fiber-optic cables.

Note

Cisco MDS 9396T Multilayer Fabric Switch Hardware Installation Guide

29

Installing the Cisco MDS 9396T Switch

Preinstallation Guidelines

«
...
33
34
35
36
37
...
»

Содержание MDS 9396T





































































Отзывы:

Нет отзывов

Похожие инструкции для MDS 9396T

Бренд: Fantech Страницы: 4

Бренд: Broadcast Tools Страницы: 28

Бренд: Teseq Страницы: 60

Бренд: Aruba Страницы: 6

Бренд: SMC Networks Страницы: 43

Бренд: Ableconn Страницы: 16

AVS-OCT-6448-210

Бренд: AMX Страницы: 1

Бренд: N-Tron Страницы: 20

Бренд: PRO SIGNAL Страницы: 2

SI1P-SH-DVI-UCAC

Бренд: Black Box Страницы: 16

SmartSTACK ETHERNET ELS10-27

Бренд: Cabletron Systems Страницы: 126

Instant On 1930 Series

Бренд: Aruba Страницы: 8

Бренд: QSFPTEK Страницы: 8

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренд: H3C Страницы: 39

Бренд: Xcellon Страницы: 2

Бренд: ClimaxDigital Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды