Cisco IR800 Series Скачать руководство пользователя страница 43

Страница: 43 / 46

C H A P T E R

Technical Specifications

Provides router, port, cabling specifications, and power adapters for the device.

•

Technical Specifications, on page 41

Technical Specifications

This section provides router, port, cabling specifications, and power adapters for the device.

NOTE:

For compliance and safety information, see the

Regulatory Compliance and Safety Information for

Cisco IR800 Series Routers.

Router Specifications

The following information lists the operational limits of the Cisco IR807. Operating the router outside of the
limits specified is not supported.

Table 6:

Physical Characteristics

Design Specification

Description

(height x width x depth x) are 1.85" x 5.07" x 4.50" (4.69 x 12.85 x 11.43 cm).

Dimensions (H x W x D)

Table 7:

Environmental Operating Ranges

Design Specification

Description

-40° to 140°F (-40° to 60°C) in a sealed NEMA cabinet with no airflow

-40° to 158°F (-40° to 70°C) in a vented cabinet with 40 lfm of air

-40° to 167°F (-40° to 75°C) in a forced air enclosure with 200 lfm of air

(type tested at +85C for 16 hours)

NOTE:

This product has been safety certified up to 60C maximum ambient.

-500 to 5,000 feet. Derate max operating temperature 1.5°C per 1000 feet. 10,000 ft maximum

Operating Temperature and Altitude

13,800 ft. (4206m)

Operating Altitude

Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide

Содержание IR800 Series















































Результаты поиска

Содержание IR800 Series

Отзывы:

Похожие инструкции для IR800 Series

Бренды по названию

Популярные бренды

Cisco IR800 Series, Руководство по установке оборудования

Результаты поиска

Содержание IR800 Series

Отзывы:

Похожие инструкции для IR800 Series

Бренды по названию

Популярные бренды