Cisco IR800 Series Скачать руководство пользователя страница 44

Страница: 44 / 46

Design Specification

Description

5% — 95% non-condensing

Humidity

Table 8: Environmental Tests

Design Specification

Description

IEC 61850-3, IEEE 1613

Vibration

Half Sine (operating)

Duration = <2 ms

Velocity = 2.39 m/s

Number of shocks: A series of 6 shocks, one on each side.

IEEE 1613 and IEC61850-3

NUP T2 shock testing, non-NEBS 3396

Shock

Table 9: Certifications

Design Specification

Description

UL 60950-1, 2nd edition

CAN/CSA C22.2 No. 60950-1, 2nd edition

EN 60950-1, 2nd edition

CB to IEC 60950-1, 2nd edition with all group differences and national deviations

Standard Safety Certifications

EN55022/CISPR22, CFR 47 Part 15, ICES003, VCCI-V-3, AS/NZS CISPR22, CNS13438, EN300-
386, EN61000-3-2, EN61000-3-3, and EN55032/CISPR32

EMC Emissions

EN55024/CISPR24, (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6,
EN61000-4-11), EN55035/CISPR35, and EN300-386

EMC Immunity

EN 301 908-1, EN 301 908-2, EN 301 511, and EN 301 908-13

Cellular Radio

IP30 compliant when vertical and cables downward.

Compliance

EN301 489-1, EN 303 413, EN 301 489-19, EN 301 489-52, and EN 62311

Radio Immunity

Table 10: Transportation/Storage Conditions

Design Specification

Description

-40 to +85°C (–40 to +185°F)

Temperature

10 – 95%

Humidity

4570 m (15,000 ft)

Altitude

Cisco IR807 Industrial Integrated Services Router Hardware Installation Guide

Technical Specifications

Router Specifications

Содержание IR800 Series















































Результаты поиска

Содержание IR800 Series

Отзывы:

Похожие инструкции для IR800 Series

Бренды по названию

Популярные бренды

Cisco IR800 Series, Руководство по установке оборудования

Результаты поиска

Содержание IR800 Series

Отзывы:

Похожие инструкции для IR800 Series

Бренды по названию

Популярные бренды