background image

1-6

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1      Installing the FlexWAN and Enhanced FlexWAN Modules

  Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Installing a FlexWAN or Enhanced FlexWAN Module Port 
Adapter

This section describes how to install a port adapter in the FlexWAN or Enhanced FlexWAN module in the 
Catalyst 6500 series switches or Cisco 7600 series routers. 

You can install port adapters in either port adapter bay 0 or port adapter bay 1. 

Figure 1-4

 shows one 

PA-H port adapter installed in port adapter bay 0 on a FlexWAN or Enhanced FlexWAN module.

Figure 1-4

Port Adapter Installed in Bay 0

Required Tools and Equipment

You need the following tools and equipment to install a port adapter. If you need additional equipment, 
contact a service representative for ordering information.

Any specific cables for your port adapter

Number 2 Phillips screwdriver

Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist 
strap included with all upgrade kits, field-replaceable units (FRUs), and spares

Antistatic mat

Antistatic container

29845

ST

ATUS

ENABLED

HSSI

Rev. B

TD

TC

RD

RC

LB/C

0

1

Port adapter
blank in bay 1

Port adapter
securing screw

Port adapter handles not shown

Port adapter

in bay 0

Содержание Enhanced FlexWAN











Отзывы: