background image

1-2

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1      Installing the FlexWAN and Enhanced FlexWAN Modules

  Preparing to Install the FlexWAN or Enhanced FlexWAN Module

Follow these guidelines for preventing ESD damage: 

Always use an ESD wrist or ankle strap, and ensure that it makes maximum contact with the skin. 
Make sure that the wrist or ankle strap is in contact with bare skin. 

Avoid contact between the printed circuit boards and clothing. The wrist strap only protects 
components from ESD voltages on the body; ESD voltages on clothing can still cause damage. 

The disposable ESD grounding strap supplied with field replaceable units (FRUs) has a metal clip 
at one end. Attach the metal clip (equipment end of the strap) to an unfinished (bare metal) chassis 
surface. 

The Catalyst 7600 series chassis also has a built-in ESD grounding connector. This is a banana plug 
connector and is identified by the ground symbol next to the connector. See 

Figure 1-1

 for an 

example of a chassis ESD wrist strap connection. 

When installing a component, use any available ejector levers or captive installation screws to 
properly seat the bus connectors in the backplane or midplane. These devices prevent accidental 
removal, provide proper grounding for the system, and help to ensure that bus connectors are 
properly seated. 

When removing a component, use any available ejector levers or captive installation screws to 
release the bus connectors from the backplane or midplane. 

Handle carriers by available handles or edges only; avoid touching the printed circuit boards or 
connectors. 

Place a removed component board-side-up on an antistatic surface or in a static shielding container. 
If you plan to return the component to the factory, immediately place it in a static shielding 
container. 

Never attempt to remove the printed circuit board from the metal carrier. 

Caution

For safety, periodically check the resistance value of the antistatic strap. The measurement should be 
between 1 and 10 megohms (Mohm). 

Figure 1-1

Example of Chassis ESD Wrist Strap Ground

113742

o

o

PS1

PS2

FAN

LINK

SLOT 2

SLOT 1

PCMCIA

EJECT

AUX 

CONSOLE

Enet

RX

TX

RESET

SWITCH/PROCESSOR

TX

UT

P3

UT

P3

UT

P3

UT

P3

RX

UTP

TX

RX

TX

RX

TX

RX

0

1

2

3

TX

UT

P3

UT

P3

UT

P3

UT

P3

RX

UTP

TX

RX

RX

TX

RX

0

1

2

3

ESD wrist strap

ESD ground strap 
connector

Содержание Enhanced FlexWAN











Отзывы: