Cisco CCNA 2 Скачать руководство пользователя страница 66

Страница: 66 / 239

65 - 238

CCNA 2: Routers and Routing Basics v3.1 Instructor Guide – Module 6

2004, Cisco Systems, Inc.

6.1.3 Configuring static routes

Use the following steps to configure static routes:

1. Determine all desired destination networks, their subnet masks, and their gateways. A

gateway can be either a local interface or a next hop address that leads to the desired
destination.

2. Enter global configuration mode.

3. Type

the

ip route

command with the address and subnet mask of the destination

followed by their corresponding gateway from Step 1. An administrative distance is
optional.

4. Repeat Step 3 for as many destination networks as were defined in Step 1.

5. Exit global configuration mode.

6. Save the active configuration to NVRAM by using the

copy running-config

startup-config

command.

Here is an example of a route from Rt1 to network 192.168.2.0.

Rt1#

config terminal

Enter configuration commands, one per line. End with CNTL/Z.
Rt1(config)#

ip route 192.168.2.0 255.255.255.0 192.168.1.2

Rt1(config)#

exit

Rt1#
Rt1#

copy running-config startup-config

Destination filename [startup-config]?
Building configuration...
Rt1#

All routers must be configured. If Rt2 does not have a route back to network 192.168.0.0, a
ping from network 192.168.0.0 will make it to network 192.168.2.0, but will not know how to
get back. A relevant TI from CCNA 2 v2.1.4 is 12.1.4.

Содержание CCNA 2














































































































































































































































Результаты поиска

Содержание CCNA 2

Отзывы:

Похожие инструкции для CCNA 2

Бренды по названию

Популярные бренды

Cisco CCNA 2, Инструкция для инструктора

Результаты поиска

Содержание CCNA 2

Отзывы:

Похожие инструкции для CCNA 2

Бренды по названию

Популярные бренды