manualshive.com logo in svg

Cisco Catalyst 9400 Series, Руководство по установке оборудования

Поделиться
Скачать
Cisco Catalyst 9400 Series Скачать руководство пользователя страница 43

• Ensure that the AC-input power supply module has a detachable power cord.

• Each chassis power supply should have a separate, dedicated branch circuit.

• North America

• C9400-PWR-3200AC only—Power supply modules require a 20 A circuit.

• C9400-PWR-2100AC only—Power supply modules require a 15 A circuit.

• International—Circuits should be sized according to local and national codes.

• If you are using a 208 or 240 VAC power source in North America, note that such lines are considered

hot and the circuit must be protected by a two-pole circuit breaker.

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than these values
for the U.S. and EU:

• 20 A circuit breaker for an AC-input power supply module.

• 50 A DC-rated circuit breaker for each input of a DC-input power supply

module, for safety purposes - irrespective of whether the inputs are power
from a single or separate DC sources.

Statement 1005

Warning

This product requires short-circuit (overcurrent) protection, to be provided as
part of the building installation. Install only in accordance with national and local
wiring regulations.

Statement 1045

Warning

A readily accessible two-poled disconnect device must be incorporated in the
fixed wiring.

Statement 1022

Warning

• The source AC outlet must be within 9.84 to 14 feet (3.0 to 4.293 meters) of the system - depending on

the length of the power cord, and should be easily accessible.

• The AC power receptacles used to plug in the chassis must be the grounding type. The grounding

conductors that connect to the receptacles should connect to protective earth ground at the service
equipment level.

Power Connection Guidelines for DC-Powered Systems

When connecting DC-input power supply modules to the site power source, observe the guidelines described
here.

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

37

Preparing for Installation

Power Connection Guidelines for DC-Powered Systems

Содержание Catalyst 9400 Series

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды