Cisco Catalyst 9400 Series Скачать руководство пользователя страница 153

Страница: 153 / 192

Catalyst 9410R Switch Chassis Specifications

Table 13: Physical Specifications of the Chassis

Specification

Item

22.61 x 17.30 x 16.30 in. (57.43 x 43.94 x 41.40 cm)

Dimensions (H x W x D)

13 RU

Rack units (RU

)

Chassis with fan tray—65.0 lb (29.48 kg)

Weight

The chassis height is measured in rack units (RU or just U), where 1 RU or 1 U equals 1.75 in (44.45
mm).

Table 14: Environmental Specifications of the Chassis

Specification

Item

• 23° to 113°F (-5 to +45ºC), up to 6,000 feet (1800 m)

• 23° to 104°F (-5 to +40ºC), up to 10,000 feet (3000 m)

Ambient

temperature

and altitude for normal
operations

• 23° to 131°F (-5 to +55ºC), up to 6,000 feet (1800 m)

• 23° to 122°F (-5 to +50ºC), up to 10,000 feet (3000 m)

Ambient

temperature

and

altitude

for

short-term conditions

exceptional conditions

-40° to 167°F (-40° to 75°C)

Nonoperating

and

storage

Hot to cold—at a maximum rate of 86°F (30°C) per hour

Cold to hot—at maximum rate of 204.8°F (96°C) per hour

Thermal transition

Operating, nonoperating and storage —10 to 95 percent

Humidity (RH), ambient
(noncondensing)

-60 to 3000m

Altitude (operating and
nonoperating)

LpAD—60 dBA

LwAD—no greater than 7.8 Bels

This is with eight power supply modules installed and delivering 50 percent of
rated output power; measured according to International Organization for
Standardization (ISO) 7779 and declared according to ISO 9296.

Sound pressure level
(LpAD)

and

sound

power level (LwAD)

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

147

Specifications

Catalyst 9410R Switch Chassis Specifications

Содержание Catalyst 9400 Series

































































































































































































Результаты поиска

Содержание Catalyst 9400 Series

Отзывы:

Бренды по названию

Популярные бренды

Cisco Catalyst 9400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 9400 Series

Отзывы:

Бренды по названию

Популярные бренды