manualshive.com logo in svg

Cisco Catalyst 9400 Series, Руководство по установке оборудования

Поделиться
Скачать
Cisco Catalyst 9400 Series Скачать руководство пользователя страница 180

Installing and Uninstalling the USB Driver

Installing the Cisco Microsoft Windows USB Device Driver

A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the USB
console port on the switch.

Installing the Cisco Microsoft Windows 7 USB Driver

Procedure

Step 1

Obtain the Cisco USB console driver file from the Cisco.com web site and unzip it.

You can download the driver file from the Cisco.com site for downloading the switch software.

Note

Step 2

If using 32-bit Windows 7, double-click the setup.exe file in the Windows_32 folder. If using 64-bit Windows
7, double-click the setup(x64).exe file in the Windows_64 folder.

Step 3

The Cisco Virtual Com InstallShield Wizard begins. Click

Next

.

Step 4

The Ready to Install the Program window appears. Click

Install

.

If a User Account Control warning appears, click

Allow - I trust this program

to proceed.

Note

Step 5

The InstallShield Wizard Completed window appears. Click

Finish

.

Step 6

Connect the USB cable to the PC and the switch console port. The USB console port LED turns green, and
the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation.

Uninstalling the Cisco Microsoft Windows USB Driver

Uninstalling the Cisco Microsoft Windows 7 USB Driver

Before you begin

Disconnect the switch console terminal before uninstalling the driver.

Procedure

Step 1

Run setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Click

Next.

Step 2

The InstallShield Wizard for Cisco Virtual Com appears. Click

Next.

Step 3

When the Program Maintenance window appears, select the Remove radio button. Click

Next.

Step 4

When the Remove the Program window appears, click

Remove.

If a User Account Control warning appears, click

Allow - I trust this program to proceed

.

Note

Cisco Catalyst 9400 Series Switches Hardware Installation Guide

174

Initial Configuration for the Switch

Installing and Uninstalling the USB Driver

Содержание Catalyst 9400 Series

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды