Cisco CableCARD Скачать руководство пользователя страница 163

Страница: 163 / 184

Adding an HDD Test Server to the BFS

734375 Rev H

153

Verifying the Success of the HDD Test Server

Select a DVR in your headend that meets the following specifications:



For Explorer 8000, 8010, or 8300 DVRs — DVR 1.5.2-1404 or later is installed
on the DVR.



For Explorer 8300HDC DVRs — DVR 1.5.3 or later is installed on the DVR.



The DVR is connected to your DBDS network.



The HDD is known to be in good operating order.

Reboot the DVR that you selected in step 1. When the DVR reboots, the SARA
client does the following:



Reads the testparam.cfg file.



Finds the appropriate entry for the DVR type.



Obtains the HDD performance specifications for the DVR type.



Stores this data in nonvolatile memory (NVM).

Note:

After the HDD test has been downloaded to the DVR, the HDD test utility

can be run without a DBDS network connection.

Place the remote in Cable mode by pressing the

key on the remote control.

The CBL key blinks red when pressing it to indicate that it is in Cable mode.

Press and hold the

Pause

key on the remote control until the message indicator

(

) on the DVR blinks.

While the message indicator blinks, quickly press the

key to activate the

Staging Toolkit.

Note:

To activate the Staging Toolkit, you must press the

key while the

message indicator is blinking. The message indicator blinks for about 13 seconds.

When the DVR display changes from displaying the time to displaying the EMM
count (for example, E-00) the Staging Toolkit is active.

Press the

Last

key three times to start the HDD test utility. The DVR display

alternately flashes

hdd

and

diAg

while the HDD test utility runs. The test takes

only a few minutes to complete.

Does

PASS

appear on the DVR display?



yes

, you have verified the success of the HDD Tests server. Press the

key to exit the HDD test utility. As the utility exits, the front panel LED
shows four dashes (

–

) and the set-top reboots.



, the HDD test utility is not functioning as expected. Contact Cisco

Services for assistance troubleshooting the HDD test utility.

Содержание CableCARD

























































































































































































Результаты поиска

Содержание CableCARD

Отзывы:

Похожие инструкции для CableCARD

Бренды по названию

Популярные бренды

Cisco CableCARD, Руководство по эксплуатации

Результаты поиска

Содержание CableCARD

Отзывы:

Похожие инструкции для CableCARD

Бренды по названию

Популярные бренды