Cisco CableCARD Скачать руководство пользователя страница 114

Страница: 114 / 184

Chapter 9 Troubleshooting

104

734375 Rev H

PowerKEY/EA Issues

This section provides a list of suggested solutions for problems that result from
PowerKEY Conditional Access or EA.

Symptom

Diagnostic
Screen

Type of
DHCT

Possible Solution

No
Entitlement
Agent (EMMs)

Page 4

Unstaged

Does the DHCT's MAC address match the MAC address
recorded in the billing system?

–

If yes

, follow these steps:

Confirm that the actual MAC address for the DHCT
matches the MAC address recorded in the DNCS.

Confirm that the Secure Micro Address for the
DHCT matches the Secure Micro Address recorded
in the DNCS.

iii

Ask the DNCS operator to perform a

modDhctCfg -s [MAC address of the DHCT]

the DHCT.

Stage the DHCT again.

–

If no

, follow these steps:

Ask the DNCS operator to correct any existing mis-
matches.

Stage the DHCT again.

iii

Go to step 2 if these actions do not remedy the
situation.

Follow these steps:

Take the DHCT out of service.

Try to stage the DHCT again.

Follow these steps:

Delete the DHCT from the DNCS.

Try to stage the DHCT again using the new EMMs.

If these steps do not work, return the DHCT to us for repair.
Mark the repair tag with

S1. No EMMs/ISE/EA.

Содержание CableCARD

























































































































































































Результаты поиска

Содержание CableCARD

Отзывы:

Похожие инструкции для CableCARD

Бренды по названию

Популярные бренды

Cisco CableCARD, Руководство по эксплуатации

Результаты поиска

Содержание CableCARD

Отзывы:

Похожие инструкции для CableCARD

Бренды по названию

Популярные бренды