Cisco C3850-NM-4-1G Скачать руководство пользователя страница 6

Страница: 6 / 16

Network Module LEDs

Figure 7: Network Module LEDs

G3 LED

G1 LED

G4 LED

G2 LED

Network Module Link Status

Color

Link is off.

Off

Link is on; no activity.

Green

Activity on a link; no faults.

The LED will blink green even when there is very little control traffic.

Note

Blinking green

Link is off due to a fault or because it has exceeded a limit set in the switch software.

Link faults occur when noncompliant cabling is connected to an SFP/SFP+
port. Use only standard-compliant cabling to connect to Cisco SFP/SFP+ ports.
You must remove from the network any cable or device that causes a link fault.

Caution

Blinking amber

Link for the SFP/SFP+ has been disabled.

Amber

Catalyst 3850 Switch Hardware Installation Guide

OL-26779-05

Installing a Network Module

Network Module LEDs

Содержание C3850-NM-4-1G

















Результаты поиска

Содержание C3850-NM-4-1G

Отзывы:

Похожие инструкции для C3850-NM-4-1G

Бренды по названию

Популярные бренды

Cisco C3850-NM-4-1G, Установка

Результаты поиска

Содержание C3850-NM-4-1G

Отзывы:

Похожие инструкции для C3850-NM-4-1G

Бренды по названию

Популярные бренды