Cisco C3850-NM-4-1G Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 16

background image

Action

Interface

Configure this interface

TenGigabitEthernet1/1/1

Configure this interface

TenGigabitEthernet1/1/2

Configure this interface

TenGigabitEthernet1/1/3

Configure this interface

TenGigabitEthernet1/1/4

Configure this interface

TenGigabitEthernet1/1/5

Configure this interface

TenGigabitEthernet1/1/6

Configure this interface

TenGigabitEthernet1/1/7

Configure this interface

TenGigabitEthernet1/1/8

Removing a Network Module

The switch complies with EMC, safety, and thermal specifications when a network module is present. If
no uplink ports are required, install a blank network module.

Note

To avoid authentication failure and non-detection of modules, wait for a minimum of five seconds between
the online insertion and removal (OIR) of network modules.

Note

Procedure

Step 1

Attach an ESD-preventive wrist strap to your wrist and to an earth ground surface

Do not remove the network module with connected cables or installed SFP modules. Always
remove any cables and modules before you remove the network module.

Caution

A module interface might become error-disabled when a network module with connected fiber-optic
cables is installed or removed. If an interface is error-disabled, you can reenable the interface by
using the

shutdown

and

no shutdown

interface configuration commands.

Caution

Step 2

Disconnect the cables from the SFP modules.

Step 3

Remove the SFP modules from the network module.

Step 4

Loosen the captive screws that hold the network module in place.

Catalyst 3850 Switch Hardware Installation Guide

OL-26779-05

13

Installing a Network Module

Removing a Network Module

«
...
11
12
13
14
15
...
»

Содержание C3850-NM-4-1G

















Отзывы:

Нет отзывов

Похожие инструкции для C3850-NM-4-1G

Бренд: Eaton Страницы: 50

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: olympia electronics Страницы: 10

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: Xilinx Страницы: 2

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

Бренд: Motrona Страницы: 10

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Бренд: SILENTRON Страницы: 20

Бренд: MacroAir Technologies Страницы: 32

Бренд: Widex Страницы: 17

Бренд: Daikin Страницы: 150

McDonnell & Miller PSE-80 Series

Бренд: Xylem Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды