Cisco C3850-NM-4-1G Скачать руководство пользователя страница 15

Страница: 15 / 16

Procedure

Step 1

Attach an ESD-preventive wrist strap to your wrist and to an earth ground surface.

Step 2

Find the send (TX) and receive (RX) markings that identify the top of the SFP module.
On some SFP modules, the send and receive (TX and RX) markings might be shown by arrows that show the
direction of the connection.

Step 3

If the SFP module has a bale-clasp latch, move it to the open, unlocked position.

Step 4

Align the module in front of the slot opening, and push until you feel the connector snap into place.

Figure 9: Installing an SFP Module in the Network Module

Step 5

If the module has a bale-clasp latch, close it to lock the SFP module in place.

Step 6

Remove the SFP dust plugs and save.

Step 7

Connect the SFP cables.

Figure 10: Network Module with SFP Modules Installed

Catalyst 3850 Switch Hardware Installation Guide

OL-26779-05

Installing a Network Module

Installing SFP and SFP+ Modules

Содержание C3850-NM-4-1G

















Результаты поиска

Содержание C3850-NM-4-1G

Отзывы:

Похожие инструкции для C3850-NM-4-1G

Бренды по названию

Популярные бренды

Cisco C3850-NM-4-1G, Установка

Результаты поиска

Содержание C3850-NM-4-1G

Отзывы:

Похожие инструкции для C3850-NM-4-1G

Бренды по названию

Популярные бренды