background image

Table 1: C3850-NM-4-1G Module

Action

Interface

Configure this interface

GigabitEthernet1/1/1

Configure this interface

GigabitEthernet1/1/2

Configure this interface

GigabitEthernet1/1/3

Configure this interface

GigabitEthernet1/1/4

Disregard

TenGigabitEthernet1/1/1

Disregard

TenGigabitEthernet1/1/2

Disregard

TenGigabitEthernet1/1/3

Disregard

TenGigabitEthernet1/1/4

C3850-NM-4-10G Module

All ports in the C3850-NM-4-10G module default to 10 G and should be configured as TenGigabitEthernet1/1/1
through TenGigabitEthernet1/1/4, even when you are operating them as 1 G using SFPs. Only four interfaces
are valid; the other four should not be used even though they still show up in the CLI.

Table 2: C3850-NM-4-10G Module

Action

Interface

Disregard

GigabitEthernet1/1/1

Disregard

GigabitEthernet1/1/2

Disregard

GigabitEthernet1/1/3

Disregard

GigabitEthernet1/1/4

Configure this interface

TenGigabitEthernet1/1/1

Configure this interface

TenGigabitEthernet1/1/2

Configure this interface

TenGigabitEthernet1/1/3

Configure this interface

TenGigabitEthernet1/1/4

   Catalyst 3850 Switch Hardware Installation Guide

10

OL-26779-05   

Installing a Network Module

Network Module Port Configurations

Содержание C3850-NM-4-1G

















Отзывы: