manualshive.com logo in svg

Cisco ASA 5508-X, Руководство по настройке

Cisco ASA 5508-X - качественный продукт для защиты сети. Скачайте бесплатно Руководство по установке оборудования на нашем сайте. Получите все необходимые инструкции для установки и настройки вашего устройства. manualshive.com - ваш надежный источник руководств.

Поделиться
Скачать
background image

 

17-11

Cisco ASA Series Firewall CLI Configuration Guide

 

Chapter 17      Quality of Service

  Configuration Examples for Priority Queuing and Policing

Configuration Examples for Priority Queuing and Policing

The following sections provide examples of configuring priority queuing and policing.

Class Map Examples for VPN Traffic

In the following example, the 

class-map

 command classifies all non-tunneled TCP traffic, using an ACL 

named tcp_traffic:

hostname(config)# 

access-list tcp_traffic permit tcp any any

hostname(config)# 

class-map tcp_traffic

hostname(config-cmap)# 

match access-list tcp_traffic

In the following example, other, more specific match criteria are used for classifying traffic for specific, 
security-related tunnel groups. These specific match criteria stipulate that a match on tunnel-group (in 
this case, the previously-defined Tunnel-Group-1) is required as the first match characteristic to classify 
traffic for a specific tunnel, and it allows for an additional match line to classify the traffic (IP differential 
services code point, expedited forwarding).

hostname(config)# 

class-map TG1-voice

hostname(config-cmap)# 

match tunnel-group tunnel-grp1

hostname(config-cmap)# 

match dscp ef

In the following example, the 

class-map

 command classifies both tunneled and non-tunneled traffic 

according to the traffic type:

hostname(config)# 

access-list tunneled extended permit ip 10.10.34.0 255.255.255.0

192.168.10.0 255.255.255.0

hostname(config)# 

access-list non-tunneled extended permit tcp any any

hostname(config)# 

tunnel-group tunnel-grp1 type IPsec_L2L

hostname(config)# 

class-map browse

hostname(config-cmap)# 

description "This class-map matches all non-tunneled tcp traffic."

hostname(config-cmap)# 

match access-list non-tunneled

hostname(config-cmap)# 

class-map TG1-voice

hostname(config-cmap)# 

description "This class-map matches all dscp ef traffic for

tunnel-grp 1."

hostname(config-cmap)# 

match dscp ef

hostname(config-cmap)# 

match tunnel-group tunnel-grp1

hostname(config-cmap)# 

class-map TG1-BestEffort

hostname(config-cmap)# 

description

 

"This class-map matches all best-effort traffic for

tunnel-grp1."

hostname(config-cmap)# 

match tunnel-group tunnel-grp1

hostname(config-cmap)# 

match flow ip destination-address

The following example shows a way of policing traffic within a tunnel, provided the classed traffic is not 
specified as a tunnel, but does go 

through

 the tunnel. In this example, 192.168.10.10 is the address of 

the host machine on the private side of the remote tunnel, and the ACL is named “host-over-l2l”. By 
creating a class-map (named “host-specific”), you can then police the “host-specific” class before the 
LAN-to-LAN connection polices the tunnel. In this example, the “host-specific” traffic is rate-limited 
before the tunnel, then the tunnel is rate-limited:

hostname(config)# 

access-list host-over-l2l extended permit ip any host 192.168.10.10

hostname(config)# 

class-map host-specific

hostname(config-cmap)# 

match access-list host-over-l2l

Содержание ASA 5508-X













































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASA 5508-X

3Com CoreBuilder 9000 Removal And Replacement Manual preview
CoreBuilder 9000
Бренд: 3Com Страницы: 12
3Com CoreBuilder 9000 Manual preview
CoreBuilder 9000
Бренд: 3Com Страницы: 8
HPE 12901E Product End-Of-Life Disassembly Instructions preview
12901E
Бренд: HPE Страницы: 5
Mitsubishi Electric 55624R(S)-MF Service Manual preview
55624R(S)-MF
Бренд: Mitsubishi Electric Страницы: 180
F5 ARX 1000 Replacement preview
ARX 1000
Бренд: F5 Страницы: 11
Quanmax MITX-V1K0 Series User Manual preview
MITX-V1K0 Series
Бренд: Quanmax Страницы: 96
National Instruments PXI 1000B User Manual preview
PXI 1000B
Бренд: National Instruments Страницы: 61
Dell PowerConnect B-DCX-4S Backbone Hardware Reference Manual preview
PowerConnect B-DCX-4S Backbone
Бренд: Dell Страницы: 134
Dell Force10 E300 Configuration Manual preview
Force10 E300
Бренд: Dell Страницы: 1262
National Instruments PXI EXPRESS PXIe-1095 Calibration Procedure preview
PXI EXPRESS PXIe-1095
Бренд: National Instruments Страницы: 6
ADTRAN Total Access 1500 Installation And Maintenance Manual preview
Total Access 1500
Бренд: ADTRAN Страницы: 8
ADTRAN MX2820 Quick Start Manual preview
MX2820
Бренд: ADTRAN Страницы: 2
Predator PO5-640 User Manual preview
PO5-640
Бренд: Predator Страницы: 32
ADC DSX-4U-24 Installation Manual preview
DSX-4U-24
Бренд: ADC Страницы: 34
ZyXEL Communications IES-5000 Series Specifications preview
IES-5000 Series
Бренд: ZyXEL Communications Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды