Cisco Aironet 1530 Series, 1532 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 69

background image

2-14

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Chapter 2 Installing the Access Point

Mounting the Access Point

Step 3

Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do
not screw the bolt all the way in; leave approximately a 0.13 inch (3.3 mm) space.

Step 4

Position the four bolts on the access point into the keyhole slots on the mounting bracket.

Step 5

Slide the access point down to sit securely in the quick mount notches.

Step 6

Using a 10mm wrench, secure the AP to the bracket by tightening the bolts to the bracket; torque to 40
lb-in.

Step 7

Continue with the

Grounding the Access Point, page 2-40

Pole Mounting the Access Point with the Fixed Mount Kit

The optional fixed mounting kit contains a mounting bracket for wall mounting or pole mounting.This
kit can be used to install the access point on a pole, mast or streetlight. It supports metal, wood or
fiberglass poles from 2 to 8 inches in diameter.

Table 2-2

Materials Needed to Mount the AP on a Vertical Pole

To mount the access point onto a vertical pole or streetlight pole, follow these steps:

Step 1

Select a mounting location on the pole to mount the access point. You can attach the access point to any
pole with a diameter from 2to 8 inches (5.1 to 20.1 cm).

Note

If you will be using a streetlight power tap adapter, position the access point within 3 ft (1 m) of
the outdoor light control. The AC/DC adapter must be used with street light power tap.

Step 2

Determine which size of band clamp is needed based on the pole diameter. Slide the two clamps through
the top and bottom set of mounting slots (see

) and mount the bracket to the pole.

Step 3

Wrap the band clamps around the pole and slide them into the second set of top and bottom mounting
slots on the bracket. Lightly tighten the clamps. Only tighten them enough to keep the bracket from
sliding down the pole.

Materials Needed to Mount the AP on a Vertical Pole

In Kit

One wall mount bracket

Yes

Four M6 x12mm hex head bolts

Yes

Two stainless steel band clamps (adjustable 2"–5", 51–127
mm)

Yes

Two stainless steel band clamps (adjustable 5"–8", 127–203
mm)

Yes

10 mm box-end wrench

No

Outdoor rated shielded ethernet cable

No

Ground lug (provided with the access point)

Yes

Ground block and rod

No

Crimping tool for ground lug, Panduit CT-720 with CD-720-1
die (

http://www.panduit.com

)

No

#6 AWG ground wire

No

«
...
44
45
46
47
48
...
»

Содержание Aironet 1530 Series, 1532






































































Отзывы:

Нет отзывов

Похожие инструкции для Aironet 1530 Series, 1532

Бренд: Raymarine Страницы: 20

Бренд: Zenitel Страницы: 29

Бренд: Ubiquiti Страницы: 32

AR 18-3XE/18-21X Series

Бренд: H3C Страницы: 79

RailBox 11ac/WiFi 5

Бренд: Acksys Страницы: 36

Бренд: TERABEAM Страницы: 10

Бренд: Kraun Страницы: 55

Wireless LAN Access Point

Бренд: Hama Страницы: 2

Бренд: ARGtek Страницы: 14

Бренд: Pakedge Device & Software Страницы: 57

Бренд: Planet Networking & Communication Страницы: 2

Бренд: BAZOO Страницы: 2

Бренд: AirLive Страницы: 51

Бренд: Steren Страницы: 21

Бренд: Steren Страницы: 72

Бренд: Doiting Страницы: 19

Бренд: Viega Страницы: 2

Бренд: High-Flying Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды