Cisco Aironet 1530 Series, 1532 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 69

background image

2-3

Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide

OL-30864-01

Chapter 2 Installing the Access Point

Warnings

•

FIPS kit (AIRLAP-FIPSKIT=)

•

Lightning Arrestor kit (AIR-ACC245LA-N=)

Optional Tools and Hardware That You Supply

Tools and materials that are user-supplied are:

•

Ground lug crimping tool (Panduit CT-720 with CD-720-1 die)

•

6-AWG copper ground wire

•

10 mm open end or box wrench

•

13 mm box-end wrench or socket set

•

Adjustable wrench with opening up to 33 mm and 28 mm socket.

•

Large flat or phillips screw driver (for port plugs)

•

Small flat screwdriver for DC power connector

•

Optional shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.20 to 0.35 in
(0.51 to 0.89 cm) diameter

•

Optional Ethernet RJ-45 connector and installation tool

•

Optional shielded outdoor-rated DC power cable with 0.20 to 0.35 inch (.0.51 to 0.89 cm) diameter

•

Optional ground rod, as required by local regulations

•

Optional ladder, power lift, rope, or other tools as required

Warnings

Translated versions of all safety warnings are available in the safety warning document that shipped with
your access point or on Cisco.com. To browse to the document on Cisco.com, refer to

“Translated Safety Warnings”

for instructions.

Warning

IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

This equipment is to be installed by trained and qualified personnel, as per these installation
instructions. The installer is responsible for obtaining any required local or national safety
inspections of the structural integrity of the installation by the local authority/inspection department.

Warning

Do not operate the unit near unshielded blasting caps or in an explosive environment unless the
device has been modified to be especially qualified for such use.

Statement 364

«
...
33
34
35
36
37
...
»

Содержание Aironet 1530 Series, 1532






































































Отзывы:

Нет отзывов

Похожие инструкции для Aironet 1530 Series, 1532

OfficeConnect 3CRWDR100B-72

Бренд: 3Com Страницы: 118

LiteAP ac LAP-120

Бренд: Ubiquiti Страницы: 24

SmartNode 5480 Series

Бренд: Patton Страницы: 58

Бренд: Digisol Страницы: 142

Бренд: Lancom Страницы: 9

Бренд: MOBIDATA Страницы: 30

Бренд: Linksys Страницы: 25

Бренд: D-Link Страницы: 64

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 36

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 65

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды