Cisco Aironet 1430 Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 48

Cisco Aironet 1430 Series Скачать руководство пользователя страница 42

42

THIRD FCC DRAFT (CISCO CONFIDENTIAL)

Wireless Telecommunications Systems with basic restrictions or reference levels related to Human
Exposure to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum
separation distance from the antenna to maintain compliance for a general bystander is as follows:

Australia

This system has been evaluated for RF exposure for Humans as referenced in the Australian Radiation
Protection standard and has been evaluated to the ICNIRP (International Commission on
Non-Ionizing Radiation Protection) limits. The minimum separation distance from the antenna to a
general bystander is as follows:

•

AIR-BR1430Axx Series:

78

.

6

inches (

2

00cm)

•

AIR-BR1430Uxx Series: 7.9 inches (20cm)

Declaration of Conformity Statements

All the Declaration of Conformity statements related to this product can be found at the following
location:

http://www.ciscofax.com

9

Bridge Specifications

Table 9 lists the technical specifications for the 1430 series bridge.

Table 9

1430 Series Bridge Specifications

Category

Specification

Dimensions (LxWxD)

Weight

Operating temperature

Storage temperature

Humidity

Antenna

Compliance

The 1430 series bridge complies with UL 2043 for products installed in a
building’s environmental air handling spaces, such as above suspended
ceilings.

br1430gsg.fm Page 42 Thursday, November 20, 2008 1:59 PM

«
...
40
41
42
43
44
...
»

Содержание Aironet 1430 Series

















































Отзывы:

Нет отзывов