Cisco Aironet 1430 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 48

Cisco Aironet 1430 Series Скачать руководство пользователя страница 29

29

THIRD FCC DRAFT (CISCO CONFIDENTIAL)

Checking Power

You can verify the availability of power to the bridge by checking the power injector LEDs (see
Figure 8):

•

Power LED

–

Green color indicates 48 VDC is available to the power injector (see Figure 8).

–

Off indicates 48 VDC is not available to the power injector—verify that the power module is
connected to the power injector and to an AC receptacle and that AC power is available.

•

Uplink Activity LED

–

Green or blinking green color indicates the bridge is operating.

—

Blinking Amber —–

Bridge has not been detected and bridge power
is not active. This might be caused by bad
connections or a defective cable or connector.
Verify that the dual-coax cables are connected
correctly to the power injector, grounding
block, and bridge. If the cables are connected
correctly, contact technical support for
assistance.

Amber

Amber

Amber

Power injector internal memory
error—disconnect and reconnect the power
injector power plug. If the problem continues,
contact technical support for assistance.

Off

Amber

Off

Bridge is resetting the configuration to
defaults; mode button has been depressed
more than 2 seconds but less than 20 seconds.

—

Red

—

Image recovery mode, downloading new
image; mode button pressed more than 20
seconds.

Red

Red

Red

Power injector internal memory
error—disconnect and reconnect the power
injector power plug. If the problem continues,
contact technical support for assistance.

Table 8

Power Injector LED Indications (continued)

Uplink Activity

Injector Status

Ethernet Activity Description

br1430gsg.fm Page 29 Thursday, November 20, 2008 1:59 PM

«
...
27
28
29
30
31
...
»

Содержание Aironet 1430 Series

















































Отзывы:

Нет отзывов