Cisco 901 Скачать руководство пользователя страница 61

Страница: 61 / 68

B-7

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

OL-23778-01

Appendix B Cable Specifications

Alarm Port Pinouts

The 1PPS interface type is Series 1.0 / 2.3, 50 ohms.

For instructions on how to configure the 10 Mhz and 1PPSs ports, see the

Cisco ASR 901 router Mobile

Wireless Software Configuration Guide

Alarm Port Pinouts

Table B-9

list the pinouts for the alarm port (RJ45) on the Cisco ASR 901 router.

Management Ethernet Port Pinouts

Table B-10

list the pinouts for the management ethernet port (RJ45) on the Cisco ASR 901 router.

Table B-8

GPS Port Pinouts for the Cisco ASR 901 router

10 Mhz

1PPS

Waveform

Input—Sine wave

Output—Square wave

Input—Pulse shape

Output—Pulse shape

Amplitude

Input— > 1.7 volt p-p

(+8 to +10 dBm)

Output— > 2.4 volts TTL
compatible

Input— > 2.4 volts TTL
compatible

Output— > 2.4 volts TTL
compatible

Impedance

50 ohms

Pulse Width

50% duty cycle

26 microseconds

Rise Time

Input—AC coupled

Output—5 nanoseconds

40 nanoseconds

Table B-9

Alarm port Pinout

Pin

Signal Name

Description

Alarm input 1

Alarm input 2

Not connected

Alarm input 3

Alarm input 4

Not connected

Содержание 901





































































Результаты поиска

Содержание 901

Отзывы:

Cisco 901, Руководство по установке, Страница: 61 / 68

Результаты поиска

Содержание 901

Отзывы: