Cisco 901 Скачать руководство пользователя страница 53

Страница: 53 / 68

A-5

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

OL-23778-01

Appendix A Troubleshooting

Reading the LEDs

T1/E1 Interface LEDs

Table A-5

summarizes the LEDs on the T1/E1 interface (available only for A901-12C-FT-D and

A901-4C-FT-D).

SFP Ethernet Interface LEDs

Table A-6

gives information about the LEDs on the SFP interface.

RJ-45 Ethernet Interface LEDs

Table A-7

summarizes the LEDs on the RJ-45 Ethernet interface.

Table A-5

T1/E1 Port LEDs

LED

Color/State

Description (two LEDs for each T1/E1 port)

Active
(labeled C,
left LED)

Green

Carrier condition—operating without problem

Yellow

Loop condition

Off

Out of service or not configured

Alarm
(labeled AL,
right LED)

Yellow

Alarm condition

Off

No alarm

Table A-6

SFP LEDs

LED

Color/State

Description

SFP Link/Active
(labeled LINK ACT)

Orange

Link and active indicator

Off

Link not enabled

Table A-7

100/1000 Ethernet Port LEDs

LED

Color/State

Description (two LEDs for each 100/1000 Ethernet port)

100/1000
RJ-45 link
(labeled L,
left LED)

Solid Green

Link with no activity

Flash Green

Link with activity

Off

No link detected

100/1000
RJ-45 speed
(labeled S,
right LED)

Green

Speed 1000

Yellow

Speed 100

Off

Содержание 901





































































Результаты поиска

Содержание 901

Отзывы:

Cisco 901, Руководство по установке, Страница: 53 / 68

Результаты поиска

Содержание 901

Отзывы: