Cisco 901 Скачать руководство пользователя страница 55

Страница: 55 / 68

B-1

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

OL-23778-01

A P P E N D I X

Cable Specifications

If you prefer to build your own cables, this appendix provides cable specifications for the Cisco ASR 901
router.

This appendix includes the following sections:

•

Gigabit Ethernet Connector Pinouts, page B-1

•

SFP Port Pinouts and Cable Specifications, page B-2

•

T1/E1 Port Pinouts, page B-2

•

Console Port Signals and Pinouts, page B-3

•

BITS Port Pinouts, page B-6

•

Time of Day Pinouts, page B-6

•

GPS Port Pinouts, page B-6

•

Alarm Port Pinouts, page B-7

•

Management Ethernet Port Pinouts, page B-7

Gigabit Ethernet Connector Pinouts

This section illustrates the Gigabit Ethernet RJ-45 connector and lists its pinout and signal descriptions.
Note that the RJ-45 ports are capable of operating in both 100BaseT and 1000BaseT modes.

Figure B-1

shows the RJ-45 connector and port, and

Table B-1

lists the connector pinouts and signals.

Figure B-1

RJ-45 Connector and Port

Table B-1

RJ-45 Connector Pinouts

Pin

FE Signal

GE Signal

TX data+

TX A+

TX data–

TX A–

20505

4567

Содержание 901





































































Результаты поиска

Содержание 901

Отзывы:

Cisco 901, Руководство по установке, Страница: 55 / 68

Результаты поиска

Содержание 901

Отзывы: