Cisco 901 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 68

Cisco 901 Скачать руководство пользователя страница 36

3-8

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

OL-23778-01

Chapter 3 Installing the Cisco ASR 901 Mobile Wireless Router

Mounting the Cisco ASR 901 Router

Wiring the DC-Input Power Source

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than 10 A minimum, 60 VDC.

Statement 1005

Complete the following steps to connect the DC power supply to the Cisco ASR 901 router:

Step 1

Switch off the DC power source at the circuit breaker, and place the circuit breaker in the Off

position.

Step 2

Locate the 6-pin terminal block (part number 27-2030-01) (

Figure 3-6

). The terminal block is located in

the accessory kit (part number 53-3085-01 for the Cisco ASR 901 router), which is shipped with the
router.

Figure 3-6

6-Pin Terminal Block

Step 3

Plug the 6-pin terminal block into the power connector located on the front side of the router.

Step 4

Connect one end of the customer-supplied power cord (16-AWG copper wire) to the site DC power
source.

Step 5

Plug the connector on the power supply cord into the 6-pin terminal block that you plugged into the rear
of the router in Step

3

.

Warning

An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure
that no exposed portion of the DC-input power source wire extends from the terminal block plug.

Statement 122

Warning

When installing this unit, secure all power cabling to avoid disturbing field-wiring connections.

Statement 38

Caution

DO NOT

power on the unit yet.

282346

«
...
34
35
36
37
38
...
»

Содержание 901





































































Отзывы:

Нет отзывов